At this stage PGP Universal Server should complete booting normally if the recovery of the file system was completed successfully. Ĩ) Reboot the computer, unmount ISO image / remove the CD from drive and complete normal boot up process. HINT: you want to run "fsck.ext3" on the partitions that are NOT mounted.Ħ) Run "fsck.ext3" command on both partitions of PGP Universal Server (sda1 and sda2):ħ) Confirm repairing of the file system when prompted with Y. SystemRescueCD - 2) Either burn the ISO to a CD in case you'll be using this procedure for physical hardware or use "Connect to Disk Image File (iso)" for accessing VMware node with VMmware console.ģ) Boot the CD / ISO image with live Linux distribution.Ĥ) Check which partitions are mounted with "mount" command.ĥ) Use "fdisk -l" command to find out on which partitions to run recovery commands (usually this will be "/dev/sda1" and "/dev/sda2" in case of PGP Universal Server 3.2). Any live linux distribution that supports ext3 can be used (e.g. Kaspersky IoT Secure Gateway 1000 will start automatically.Īfter Kaspersky IoT Secure Gateway 1000 starts for the first time, it is recommended to configure the network, create and upload an administrator certificate, configure the date and time, and replace the web server certificate with the one that is used in your organization.1) Download 3rd party live Linux distribution that contains "fsck" utility for ext3. Turn on the Advantech UTX-3117FS-S6A1N by clicking the on/off button in the right part of the front panel.Eject the bootable USB drive containing the SystemRescueCd distribution package.When installation completes, use the SystemRescueCd tools to shut down the Advantech UTX-3117FS-S6A1N by running the following command:.Use the command line to unpack the image:.The HTTP server and the Advantech UTX-3117FS-S6A1N device must reside in the same network. The Kaspersky IoT Secure Gateway 1000 installation image received in the distribution kit must be put on an HTTP server deployed in the local network in advance. $ wget %path to the installation image of Kaspersky IoT Secure Gateway 1000% Download the Kaspersky IoT Secure Gateway 1000 installation image from the internal network, for example, by using the wget utility:.Go to the directory /tmp by entering the following command in the command line:.The next time Kaspersky IoT Secure Gateway 1000 is loaded, it will apply the load settings that were configured during preparations for Kaspersky IoT Secure Gateway 1000 installation. On the Save & Exit tab, select Save Changes & Exit.Īfter Kaspersky IoT Secure Gateway 1000 is installed and the bootable USB drive is extracted, the settings defined at this step of the instructions will be reset.In the Boot Option Priorities section, use the + or - key to move the UEFI: value to the first position.Configure the settings for loading Kaspersky IoT Secure Gateway 1000 from a bootable USB drive:.The main BIOS menu of the Advantech UTX-3117FS-S6A1N device will open. Click the on/off button in the right part of the front panel of the Advantech UTX-3117.It runs from a Live CD, a USB flash drive. SystemRescue is not intended to be used as a permanent operating system. 3 The primary purpose of SystemRescue is to repair unbootable or otherwise damaged computer systems after a system crash. Insert the bootable USB drive containing the SystemRescueCd distribution package into the USB port on the Advantech UTX-3117FS-S6A1N. SystemRescue (Previously known as ' SystemRescueCD ') is a Linux distribution for x86 64 and x86 computers.The dd utility is available only in some UNIX™-based operating systems. $ dd if=systemrescuecd-6.0.3.iso of=/dev/%USB device name%
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |